Skip to content
Introductory Offer: list your rental locations free for 3 months.Start free

Rental guide

How to Rent a Hydrovac Truck: A Renter's Guide

To rent a hydrovac truck, decide whether you need the truck alone (dry hire) or the truck with a trained operator (wet hire), choose a size that fits both your dig and your roads, then get quotes from rental companies near the job and confirm in writing what each rate includes. Most full-size hydrovac trucks have a GVWR of 26,001 pounds or more, so whoever drives typically needs at least a Class B CDL. On Vac4Rent you can submit one rental request; the Vac4Rent team reviews it and sends it to rental companies near the job, who contact you directly with their own rates.

Facts checked . Sources are linked under each section.

Key takeaways

  • Decide first between dry hire (the truck only, your operator) and wet hire (the truck plus a trained operator). General contractors without hydrovac experience typically choose wet hire.
  • Most full-size hydrovac trucks have a GVWR of 26,001 pounds or more and need at least a Class B CDL. A truck or pickup towing a trailer with a GVWR over 10,000 pounds can need a Class A.
  • A fully loaded mid-size hydrovac weighs about 55,000-66,000 lbs, which is over the 54,000-pound Interstate axle total for a steer-plus-tandem truck even though it is under 80,000 pounds gross, so check loaded axle weights, route limits, and clearances before it moves.
  • Rates are quoted per day, week, or month. Get fuel, dump fees, damage, standby, deposit, and delivery terms in writing. Vac4Rent does not set or publish rates.
  • Walk the truck, run every system under load, photograph existing damage, and call 811 before anyone digs.

How do you rent a hydrovac truck, step by step?

Write the job down first, then quote it the same way with every rental company. When you compare them, check the points Hydrovac News lists for choosing a rental: the rate structure and included operating hours, delivery and pickup, and whether a qualified driver comes with the unit. The sections below take each one in turn.

  • Describe the job: location, what you are digging (potholes, daylighting, slot trenches), the soil, and how many days you need.
  • Decide who runs the truck: your own CDL-qualified operator (dry hire) or one supplied with the truck (wet hire).
  • Pick a size that fits both the dig and the roads you will drive.
  • Get quotes for the same job from rental companies near the job site.
  • Book early: rental trucks may not be available in peak season, and renting can involve booking lead time.
  • Get the rate, included hours, fuel, dump fees, damage, deposit, insurance, and delivery terms in writing before you book.

Should you rent a hydrovac, hire a crew, or buy one?

Rent when you need a hydrovac for specific jobs or project phases, hire a crew when you would rather not run the truck yourself, and buy only when you will use a truck often enough that owning costs less than renting.

Renting turns fixed equipment costs into variable costs tied to actual work, which preserves cash if your project schedule is irregular. Hydrovac News says renting fits general contractors who need a hydrovac for specific project phases, utilities with occasional potholing needs, and operators testing the market before buying. Benefits include no capital investment, paying only when you need the truck, maintenance and repairs handled by the rental company, and the chance to try different truck sizes. Drawbacks include a higher per-day cost than owning at high use, and limited choice of configuration.

With a wet hire you still rent the truck and direct the work. When you hire a crew, a hydro excavation contractor takes on the job itself. If you would rather hire a crew, Hydrovac Hotline, our sister site, is where you can submit a request for hydro excavation work. When you hire a crew, check that the contractor has proper licensing, liability insurance, and operator certifications. Ask whether billing is hourly, daily, or by the cubic yard, whether mobilization, water supply, and disposal are included, and how they handle slurry disposal, which helps avoid hidden disposal fees. Ask about their potholing procedures, pressure management, and 811 locate compliance too.

What size hydrovac truck should you rent?

Size the truck to the dig and to the roads you will drive: compact trucks suit potholing and tight urban sites, mid-size trucks suit most utility work, and industrial trucks suit pipeline, oil and gas, and remote work where cutting down on dump trips matters most.

A hydrovac truck combines a water tank (typically 400 to 1,500 gallons), a debris tank (typically 6 to 16 cubic yards), a boiler, a high-pressure water pump, a vacuum blower or fan, and a boom or hose reel on a heavy-duty chassis. The most common configuration is a 10-12 cubic yard debris tank with a 1,000-1,200 gallon water tank on a tandem rear axle chassis (56,000-66,000 lb GVWR).

For residential utility work such as potholing, daylighting, and small trenches, 8-10 cubic yards handles most jobs without dumping mid-day. Small trucks work well in residential areas, tight job sites, and on weight-restricted roads; large trucks go longer between dump trips but cannot reach every site. Trailer-mounted units carry 3-8 cubic yards, against 10-15 or more on a typical full-size truck-mounted unit.

Water capacity sets how long the crew can work before refilling. Compact units carry 400-600 gallons, standard trucks 800-1,200 gallons, and large industrial units 1,200-1,500 gallons. A 1,200-gallon tank used at 10 GPM gives about 2 hours of continuous digging. Bigger is not automatically better, because a large tank can hit the legal weight limit before it is full.

Dry hire or wet hire: who supplies the operator?

With a dry hire you rent the truck only and supply your own operator; with a wet hire the truck comes with a trained operator. General contractors without hydrovac experience typically choose wet hire.

An operator-included rental includes the truck and a trained operator, and typically fuel and maintenance. It is a turnkey option for general contractors who need hydrovac capability but do not have trained operators on staff. Wet hire costs more per day, but it removes the need for operator training and licensing and the liability of running unfamiliar equipment, so if you have someone who could run the truck, price it both ways.

If you go dry hire, look hard at who will run it. Hydrovac operators need CDL training, equipment operation certification, and H2S, confined space, and OSHA excavation safety training, and many hydrovac companies also require manufacturer-specific training and certifications in traffic control and first aid. Hydrovac News describes the swamper, or technician, as the person who supports the operator in fieldwork with hands-on excavation tasks and safety support, so think about who fills that role on your crew.

Do you need a CDL to drive a rented hydrovac?

Usually, yes. Most full-size hydrovac trucks have a GVWR of 26,001 pounds or more and require at least a Class B CDL, while some compact units under 26,001 pounds GVWR can be driven with a standard license, as long as the loaded truck also weighs under 26,001 pounds (federal rules count whichever is greater). A trailer-mounted unit can avoid the CDL only when the combination stays under the federal thresholds below.

The line comes from federal rules. 49 CFR 383.91 defines a Group B (heavy straight) vehicle as any single vehicle with a GVWR of 26,001 pounds or more, or such a vehicle towing a vehicle of 10,000 pounds GVWR or less. It defines a Group A (combination) vehicle as any combination with a gross combination weight rating of 26,001 pounds or more where the towed vehicle's GVWR is over 10,000 pounds. That is why a hydrovac truck towing a trailer with a GVWR over 10,000 pounds, with a combined rating of 26,001 pounds or more, needs a Class A CDL. The same rule covers a hydrovac trailer behind a pickup or medium-duty truck: if the trailer's GVWR is over 10,000 pounds and the combined rating is 26,001 pounds or more, the driver needs a Class A CDL. The combined figure that counts is the highest of: the tow vehicle's gross combination weight rating (GCWR) on its certification label, or the tow vehicle's and trailer's GVWRs (or their actual loaded weights, where higher) added together. A trailer also counts as over 10,000 pounds when either its GVWR or its loaded weight is. So ask for the trailer's GVWR, and check the ratings and the loaded weights before you book.

By chassis class, Hydrovac News says small Class 6 trucks with 4-8 cubic yard tanks often do not need a CDL, while Class 7 trucks (26,001-33,000 lbs) need at least a Class B. Endorsements matter too. Under federal rules, a vehicle built to carry liquid in tanks of more than 119 gallons each and 1,000 gallons or more in total is a tank vehicle, and its driver needs a tank vehicle endorsement on the CDL. Hydrovac water tanks commonly hold 800 to 1,500 gallons, so ask the rental company whether the unit is treated as a tank vehicle. Some states also have their own endorsement requirements and specific rules for operating vacuum trucks, so check your state's CDL requirements.

On a dry hire, it is on you to make sure your operator holds the right CDL class and any required endorsements. Ask the rental company for the exact unit's GVWR in writing before you book, and if nobody on your crew has the right license, ask about a wet hire instead.

How are hydrovac rental rates structured?

Hydrovac rentals are priced per day, per week, or per month, and a rate may cover just the truck (a bare rental) or a full-service package that includes an operator. Vac4Rent does not set or publish rates; each rental company quotes you directly.

Rates vary by region and truck size. Longer terms, such as monthly rentals, generally get lower per-day rates. Check how many operating hours each rate includes.

Before you sign, pin down who pays for fuel, who pays dump fees, and who covers damage beyond normal wear. On operator-included work, also ask about standby time: billable time when the equipment and crew are on site but cannot dig for reasons outside the contractor's control, such as waiting for utility locates, permits or inspections, or for other contractors to clear the work area. The standby rate, the minimum notice for cancellation, and the conditions for standby should all be spelled out in the contract or service agreement. Ask how delivery or mobilization is billed too (the delivery section below covers what goes into it).

To compare quotes fairly, send every rental company the same job details: location, dates, truck size, operator or no operator, and where the spoil will go.

What about insurance and deposits?

Insurance and deposit terms vary by rental company, so ask for them in writing before you book. In its buy vs rent comparison, Hydrovac News lists a security deposit as the upfront cost of renting, compared with a down payment for buying, and gives no deposit amount.

What is covered depends on the arrangement. Hydrovac News says operator-included (wet hire) rentals typically include maintenance, fuel, and insurance. On a dry hire your people run the truck, so it matters even more to know who covers damage beyond normal wear. Insurance coverage is one of the things Hydrovac News says to evaluate in any rental company, alongside fleet condition, maintenance standards, and who handles fuel and dumping.

Questions worth asking each rental company: What insurance do you need to carry, and do they want a certificate of insurance before the truck leaves the yard? Who pays if the truck is damaged on your site, and what counts as normal wear? How much is the deposit, when is it refunded, and what can be deducted from it?

For the work itself, Hydrovac News lists general liability, commercial auto, workers compensation, and umbrella or excess liability as a baseline for hydrovac work, and many clients also require pollution and professional liability. Some of this coverage is required by law, and most clients require it before a contractor can start work.

How heavy is a loaded hydrovac, and what are the axle weight limits?

A fully loaded mid-size hydrovac truck (10-12 cubic yard debris tank, 1,000 gallon water tank) weighs about 55,000-66,000 lbs, depending on chassis, equipment, and how dense the material is. On the Interstate Highway System, the federal maximums are 20,000 pounds on a single axle, 34,000 pounds on a tandem axle, and 80,000 pounds gross vehicle weight. On the most common setup, a steer axle plus a tandem rear axle, those axle limits add up to 54,000 pounds on the Interstate. Every loaded weight in that range is over that 54,000-pound total, even though it is well under 80,000 pounds gross, so plan to run a steer-plus-tandem truck partly loaded on the Interstate, or ask the rental company for a unit with more axles. Get the unit's loaded axle weights and check them against the limits on your route, not only the gross. Ask for the unit's axle spacing too (see the bridge formula below).

Water weighs 8.34 lbs per gallon, so 1,000 gallons is 8,340 lbs, and soil in the debris tank weighs about 2,000-2,400 lbs per cubic yard dry and 2,800-3,200 lbs saturated, so plan on the high end for wet slurry. Debris tank capacity in cubic yards is not the same as payload in pounds: available payload equals GVWR minus the empty truck weight. Check that the tank size you are offered, loaded with your typical material, will not push the truck over its chassis GVWR.

Tandem rear axles are standard on most hydrovac trucks and provide 40,000-46,000 lbs of rear axle capacity. That is equipment capacity, not the legal road limit. Staying under total GVWR also does not mean each individual axle is within its rating, so check the front and rear axle ratings separately.

The federal bridge formula, introduced in 1975, aims to reduce the risk of damage to highway bridges by requiring more axles, or a longer wheelbase, as vehicle weight rises; it applies to any group of two or more consecutive axles, so depending on how many axles a truck has and how far apart they are, it may require a lower weight than the axle limits alone. Off the Interstate, states may set their own weight standards, and bridge law compliance varies by state, so a hydrovac truck that is legal in one state may be overweight in another.

Do you need an oversize or overweight permit?

An oversize permit, if the truck is over the size limits on your route, comes from each state you travel through, not the federal government. Overweight is different: on the Interstate, overweight permits are generally for loads that cannot be split, and spoil and water can be dumped, so if the loaded truck is over its axle or gross limits, the usual answer is to carry less or rent a smaller truck, not to get a permit. FHWA lists a permit phone number and website for each state.

Size first. Typical hydrovac trucks are about 30-42 feet long including boom overhang and 11-13.5 feet tall including boom and tank, and longer trucks may need oversize permits in some jurisdictions. There is no federal vehicle height limit; state height limits run from about 13 feet 6 inches to 14 feet 6 inches, so a truck at the top of the typical height range sits right at the lowest common limit. With the boom and tank, the truck must clear bridges, overpasses, and overhead lines, so check route clearances before driving to a new area.

Then weight. Beyond the federal axle and bridge formula limits above, local roads add their own: many residential streets, bridges, and parking structures have weight limits that rule out fully loaded Class 8 trucks; small hydrovac trucks (6-10 cubic yard tanks on Class 5-7 chassis) work well on those roads.

Ask the rental company whether they handle permits for delivery or whether that falls to you, and get the unit's length, height, and axle weights so you can check your route before the truck rolls.

Pickup or delivery: how does the truck get to the job?

Ask each rental company how delivery and pickup work for your job site, how they are priced, and whether a qualified driver is available with the unit. Both are on the Hydrovac News list of things to check when choosing a rental.

Truck-mounted units move between sites at highway speed. Trailers tow more slowly and are harder to maneuver on job sites. Towing by a standard heavy-duty pickup and lower mobilization costs for local projects are among the strengths of trailer-mounted rentals, for renters who already have a suitable tow vehicle. Larger 8-cubic-yard trailers need a medium-duty tow vehicle, so check the trailer's GVWR against your tow vehicle's towing and combined ratings, and the CDL rule above, before you book.

If the truck comes to you, expect a delivery or mobilization charge for moving it from the rental yard to your site. These charges vary with distance, equipment size, and the local market. Booking one rental for several nearby jobs, rather than separate deliveries, keeps them down.

What should you inspect before you accept a rental hydrovac?

Before you accept a rental hydrovac, get a walkthrough, run every system at operating pressure and vacuum, inspect the truck itself, and photograph any existing damage. Some problems only show up under full load, so a test at idle is not enough.

Hydrovac News also advises renters to confirm that all required certifications and inspections on the unit are current, and to ask for the maintenance records. Once the truck is yours for the job, the same habit carries on: a daily pre-trip check covers the engine, vacuum system, water system, boom, hydraulics, safety equipment, and a walk-around on every operating day.

  • Get a walkthrough and confirm the safety systems work before the rental starts.
  • Run all systems at operating pressure and vacuum, not just at idle.
  • Test vacuum suction and check water pump pressure and flow.
  • Cycle the boom through full extension, retraction, and rotation, watching for binding or jerky movement.
  • Check the debris tank door seals for compression set and cracking, and confirm they hold vacuum.
  • Inspect hydraulic hoses, fittings, cylinders, and the reservoir for leaks, and check the fluid condition.
  • Check the full length of the pressure hose for cracking, bulging, or exposed reinforcement wire.
  • If the truck has a boiler, light it, check how fast the temperature rises, and test its safety shutoffs.
  • Check the brakes, lighting, tires and tread depth, safety equipment, inspection sticker, and registration.
  • Ask to see the dump cycle run, photograph existing damage, and ask for the maintenance records.

What are the red flags when renting a hydrovac?

The main red flags are a truck that leaks, smokes, or will not hold vacuum, and a rental company that cannot show records or put terms in writing. Rental trucks may not be maintained to your standards, so check fleet condition and maintenance standards before you commit.

A leaking debris tank door can contaminate roads and cause regulatory problems, worn door seals reduce vacuum performance, and a stuck dump door or failed tilt cylinder takes the truck out of service until it is repaired. Exhaust smoke color is a quick warning sign: white points to a coolant leak, blue to oil burning, and black to fuel system issues.

Know where the slurry is going before the first dig. Disposal rules vary by state, so check the rules where disposal happens, not just where the job is. Hydrovac News advises dumping at licensed landfills, slurry disposal facilities, or recycling centers that can dewater slurry for solid reuse. Under RCRA, the party that generates the waste holds primary regulatory responsibility, and on most hydrovac jobs Hydrovac News says that is the contractor.

  • A debris tank door that leaks, or door seals that are cracked or will not hold vacuum.
  • No maintenance records, or certifications and inspections that are not current.
  • No clear answer on who pays for fuel, dump fees, and damage beyond normal wear.
  • A tank size that would put the truck over its GVWR when loaded with your material.
  • No licensed disposal site lined up for the slurry.
  • A dry hire with no check of your operator's CDL class and endorsements.
  • No loaded axle weights from the rental company, or loaded axle weights above the limits on your route.

Do you need to call 811 before digging?

Yes. State law requires excavators to contact 811 before breaking ground, typically two to three business days ahead, and the exact window depends on the state. Build that notice into your rental dates so the truck is not sitting on standby waiting for locates.

811 is the national three-digit number that connects callers to their local one-call center to request utility locates before digging. The Federal Communications Commission established it in 2005, and it became operational nationwide in 2007. One-call centers do not locate or mark utilities themselves; they notify the utility operators, who send locators to mark their lines.

Once lines are marked, the tolerance zone is the area on either side of a marked utility where most states require non-destructive methods such as hydrovac or hand digging. It is defined by state law and is often 18 to 24 inches on each side of the marked utility. States measure it differently, some from the outer edge of the facility and some from the marked center line. That non-destructive requirement is a big reason crews rent a hydrovac in the first place.

Vac4Rent's state rental pages list the one-call center, notice window, and tolerance zone for each state they cover, and the Hydrovac News state regulation guides add penalties and cite the statute or rule behind each requirement.

Frequently asked questions

Do I need a CDL to drive a rented hydrovac truck?+

Usually. Most full-size hydrovac trucks have a GVWR of 26,001 pounds or more and need at least a Class B CDL, or a Class A when the truck, or a pickup, tows a trailer with a GVWR over 10,000 pounds and the combined rating is 26,001 pounds or more. Some compact units can be driven without one, so check the unit's GVWR, its loaded weight, and your state's rules.

How heavy is a fully loaded hydrovac truck?+

A fully loaded mid-size hydrovac with a 10-12 cubic yard debris tank and a 1,000 gallon water tank weighs about 55,000-66,000 lbs, depending on chassis, equipment, and how dense the material is. Water alone weighs 8.34 lbs per gallon, and saturated soil weighs about 2,800-3,200 lbs per cubic yard. That is over the 54,000-pound Interstate axle total for a steer-plus-tandem truck, even though it is under 80,000 pounds gross.

What should a hydrovac rental agreement spell out?+

Who pays for fuel, dump fees, and damage beyond normal wear, how many operating hours each rate includes, the deposit and insurance (certificate of insurance) terms, and how delivery and pickup work. Get each one in writing before the truck leaves the yard.

What should I check before I accept a rental hydrovac?+

Get a walkthrough, run every system at operating pressure and vacuum, cycle the boom, and check the door seals, hoses, brakes, and tires. Confirm that required certifications and inspections are current, photograph any existing damage, and ask for the maintenance records.

What if a loaded hydrovac is too heavy for my route?+

Check the route before the truck moves: off the Interstate, states set their own weight standards, and many residential streets, bridges, and parking structures have limits that rule out fully loaded Class 8 trucks. On the Interstate, overweight permits are generally for loads that cannot be split, so the usual answer is to carry less or rent a smaller truck built for weight-restricted roads.

How far ahead should I book a rental hydrovac?+

Book early. Rental trucks may not be available in peak season and renting can involve booking lead time, and you also need to allow for the 811 notice window, which is typically two to three business days depending on the state.

Find a hydrovac to rent

Browse rental locations, or submit one rental request and our team sends it to rental companies near the job.

Would you rather hire a hydrovac crew than rent a truck? Request a crew on Hydrovac Hotline

Vac4Rent and Hydrovac News are both published by Hydrovac News LLC.